View EUA5202_1899221.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EUA5202 ds5202 ver 1.4 nov. 2004 1 2-w stereo audio power amplifier with mute description the EUA5202 is a stereo audio power amplifier that delivering 2w of continuous rms power per channel into 3- ? loads. when driving 1w into 8- ? speakers, the EUA5202 has less than 0.04% thd+n across its specified frequency range. included within this device is integrated de-pop circuitry that virtually eliminates transients that cause noise in the speakers. amplifier gain is externally configured by means of two resistors per input channel and does not require external compensation for settings of 2 to 20 in btl mode (1 to 10 in se mode). an internal input mux allows two sets of stereo inputs to the amplifier. in notebook applications, where internal speakers are driven as btl and the line (often headphone drive) outputs are required to be se, the EUA5202 automatically switches into se mode when the btl se/ inputs is activated. consume only 7ma of supply current during normal operation, and the EUA5202 also features a shutdown function for power sensitive applications, holding the supply current at 1a. features z output power at 3 ? load - 2w/ch at v dd =5v - 800mw/ch at 3v z low supply current and shutdown current z integrated depop circuit z mute and shutdown control function z thermal shutdown protection z stereo input mux z bridge-tied load (btl) or single-ended (se) modes. z tssop-24 with thermal pad applications z notebook computers z multimedia monitors z digital radios and portable tvs block diagram
EUA5202 ds5202 ver 1.4 nov. 2004 2 typical application circuit figure 1. EUA5202 minimum configuration application circuit figure 2. EUA5202 full configuration application circuit
EUA5202 ds5202 ver 1.4 nov. 2004 3 pin configurations package pin configurations tssop-24 with thermal pad, exposure on the bottom of the package pin description pin pin i/o description line hp/ 16 i input mux control input, hold high to se lect lhp in or rhp in (5, 20), hold low to select lline in or rline in (4, 21) lbypass 6 tap to voltage divider for left channel internal mid-supply bias lhpin 5 i left channel headphone input, selected when line hp/ terminal (16) is held high lline in 4 i left channel line input, selected when line hp/ terminal (16) is held low lout+ 3 o left channel + output in btl mode, + output in se mode lout- 10 o left channel - output in btl mode, high-impedance state in se mode gnd/hs 1,12,13, 24 ground connection for circuitry, directly connected to thermal pad lv dd 7 i supply voltage input for left channel and for primary bias circuits mute in 11 i mute all amplifiers, hold low for normal operation, hold high to mute mute out 9 o follows mute in terminal (11), provides buffered output nc 17,23 no internal connection rbypass 19 tap to voltage divider for right channel internal mid-supply bias rhpin 20 i right channel headphone input, selected when line hp/ terminal (16) is held high rlinein 21 i right channel line input, selected when line hp/ terminal (16) is held low rout+ 22 o right channel + output in btl mode, + output in se mode rout- 15 o right channel - output in btl mode, high-impedance state in se mode rv dd 18 i supply voltage input for high channel btl se/ 14 i hold low foe btl mod, hold high for se mode shutdown 8 i places entire ic in shutdown mode when held high, i dd =5a t j 2 o sources a current proportional to the junc tion temperature. this terminal should be left unconnected during normal operation.
EUA5202 ds5202 ver 1.4 nov. 2004 4 ordering information order number package type marking operating temperature range EUA5202qir tssop 24 xxxx EUA5202 -40c to 85c EUA5202qit tssop 24 xxxx EUA5202 -40c to 85c EUA5202 ?? ?? ?? packing r: tape& reel t: tube operating temperature range i: industry standard package type q: tssop
EUA5202 ds5202 ver 1.4 nov. 2004 5 absolute maximum ratings ? supply voltage , v dd ------------------------------------------------------------------------------------------- 6v ? input voltage, v 1 ---------------------------------------------------------------------------- -0.3v to v dd +0.3v ? continuous total power dissipation--------------------------- ---------------------------------- internally limited ? operating free-air temperature range ,t a ------------------------------------------------------- ?40c to 85c ? operating junction temperature range, t j ------------------------------------------------------- ?40c to 150c ? storage temperature range, t stg ---------------------------------------------------------------- ?65c to 150c ? lead temperature 1,6 mm (1/16 inch) from case for 10 seconds-------------------------------------- 260c recommended operating conditions min nom max unit supply voltage, v dd 3 5 5.5 v v dd = 5v, 250m w/ch average power, 4 - ? stereo btl drive, with proper pcb design -40 85 operating free-air temperature, t a v dd = 5v, 2 w/ch average power, 3- ? stereo btl drive, with proper pcb design and 300 cfm forced-air cooling -40 85 c v dd = 5v 1.25 4.5 common mode input voltage, v icm v dd = 3.3v 1.25 2.7 v dc electrical characteristics, t a =25c EUA5202 symbol parameter conditions min. typ max. unit stereo btl 7.1 11 ma v dd =5v stereo se 3.9 6 ma stereo btl 5.7 9 ma i dd supply current v dd =3.3v stereo se 3.1 5 ma v oo output offset voltage (measured differentially) v dd =5v, gain=2 5 25 mv i dd (mute) supply current in mute mode v dd =5v 1.55 ma i dd(sd) i dd in shutdown v dd =5v 1 5 a
EUA5202 ds5202 ver 1.4 nov. 2004 6 typical ac operating characteristics, v dd =5v, t a =25c, r l =3 ? symbol parameter conditions typ. unit thd=0.2%, btl, see figure 3 2 p o output power(each channel) *1 thd=1%, btl, see figure 3 2.2 w thd+n total harmonic distortion plus noise p o =2w, f=1khz ,see figure5 200 m% v 1 =1v, r l =10k ? , a v =1v/v 100 m% b om maximum output power bandwidth av=10v/v thd <1% , see figure5 >20 khz f=1khz, see figure37 65 supply ripple rejection ratio f=20-20khz, see figure37 40 db mute attenuation 85 db channel-to- channel output separation f=1khz, see figure 39 85 db line/hp input separation 88 db btl attenuation in se mode 86 db z 1 input impedance 2 m ? signal-to-noise ratio p o =2w,btl, 5v 101 db v n output noise voltage see figure 35 22 v(rms) *1: output power is measured at the output terminals of the ic at 1 khz typical ac operating characteristics, v dd =3.3v, t a =25c, r l =3 ? symbol parameter conditions typ. unit thd=0.2%, btl, see figure 10 800 p o output power(each channel) *1 thd=1%, btl, see figure 10 900 w thd+n total harmonic distortion plus noise p o =2w, f=1khz ,see figure11 350 m% v 1 =1v, r l =10k ? , a v =1v/v 200 m% b om maximum output power bandwidth av=10v/v thd <1%, see figure11 >20 khz f=1khz, see figure37 60 supply ripple rejection ratio f=20-20khz, see figure37 40 db mute attenuation 85 db channel-to- channel output separation f=1khz, see figure 40 80 db line/hp input separation 88 db btl attenuation in se mode 86 db z 1 input impedance 2 m ? signal - to - noise ratio p o =700mw,btl, 5v 96 db v n output noise voltage see figure 36 22 v(rms) *1: output power is measured at the output terminals of the ic at 1 khz
EUA5202 ds5202 ver 1.4 nov. 2004 7 typical operating characteristics (table of graphs) no item conditions figure page 1 thd+n vs. output power vdd=5v ?a rl=3 & 8 ohm ?a btl ?a f=1khz 3 9 2 thd+n vs. frequency vdd=5v ?a rl=4 ohm ?a btl ?a po=1.5w f=20 to 20khz ?a av= -2 & -10 & -20v/v 4 9 3 thd+n vs. frequency vdd=5v ?a rl=3 & 4 ohm ?a btl ?a po=1.5w ?a f=20 to 20khz 5 9 4 thd+n vs. output power vdd=5v ?a rl=3 ohm ?a btl ?a f=20 & 1k & 20khz 6 9 5 thd+n vs. frequency vdd=5v ?a rl=8 ohm ?a btl ?a f=20 to 20khz ?a av=-2v/v 7 9 6 thd+n vs. output power vdd=5v ?a rl=8 ohm ?a btl ?a po=1w ?a av= -2 &-10 & -20v/v ?a f=20 to 20khz 8 9 7 thd+n vs. output power vdd=5v ?a rl=8 ohm ?a btl ?a f=20 & 1k & 20khz 9 10 8 thd+n vs. output power vdd=3.3v ?a rl=3 & 8 ohm ?a btl ?a f=1khz 10 10 9 thd+n vs. frequency vdd=3.3v ?a rl=4 ohm ?a btl ?a po=0.75w ?a av= -2 &-10 &-20v/v ?a f=20 to 20khz 11 10 10 thd+n vs. frequency vdd=3.3v ?a rl=4 ohm ?a btl ?a av=-2v/v ?a po=0.1 & 0.35 & 0.75w & 800mw(rl=3 ohm) 12 10 11 thd+n vs. output power vdd=3.3v ?a rl=3 ohm ?a btl ?a av=-2v/v ?a f=20 & 1k & 20khz 13 10 12 thd+n vs. frequency vdd=3.3v ?a rl=8 ohm ?a btl ?a po=0.4w ?a av=-2 &-10 & -20v/v 14 10 13 thd+n vs. frequency vdd=3.3v ?a rl=8 ohm ?a btl ?a av=-2v/v ?a po=0.1 & 0.25 & 0.4w 15 11 14 thd+n vs. output power vdd=3.3v ?a rl=8 ohm ?a btl ?a av= -2v/v ?a f=20 & 1k &20khz 16 11 15 thd+n vs. frequency vdd=5v ?a rl=4 ohm ?a se ?a po=0.5w ?a av= -1&-5&-10v/v 17 11 16 thd+n vs. frequency vdd=5v ?a rl=4 ohm ?a se ?a av= -2v/v ?a po=0.1 & 0.25 & 0.5w 18 11 17 thd+n vs. output power vdd=5v ?a rl=4 ohm ?a se ?a av= -2v/v ?a f=100 & 1k & 20khz 19 11 18 thd+n vs. frequency vdd=5v ?a rl=8 ohm ?a se ?a po=0.25w ?a av= -1 &-5 &-10v/v 20 11 19 thd+n vs. frequency vdd=5v ?a rl=8 ohm ?a se ?a av= -2v/v ?a po=0.05 & 0.1 & 0.25w 21 12 20 thd+n vs. output power vdd=5v ?a rl=8 ohm ?a se ?a av= -2v/v ?a f=100 &1k & 20khz 22 12 21 thd+n vs. frequency vdd=5v ?a rl=32 ohm ?a se ?a po=0.075w ?a av= -1 &-5 &-10v/v 23 12 22 thd+n vs. frequency vdd=5v ?a rl=32 ohm ?a se ?a av= -1v/v ?a po=25 & 50 & 75mw 24 12 23 thd+n vs. output power vdd=5v ?a rl=32 ohm ?a se ?a av= -1v/v ?a f=20 & 1k & 20khz 25 12 24 thd+n vs. frequency vdd=3.3v ?a rl=4 ohm ?a se ?a po=0.2w ?a av= -1 &-5 &-10v/v 26 12 25 thd+n vs. frequency vdd=3.3v ?a rl=4 ohm ?a se ?a av= -1v/v ?a po=0.05 & 0.1 & 0.2w 27 13 26 thd+n vs. output power vdd=3.3v ?a rl=4 ohm ?a se ?a av= -2v/v ?a f=100 & 1k & 20khz 28 13 27 thd+n vs. frequency vdd=3.3v ?a rl=8 ohm ?a se ?a po=100mw ?a av= -1 &-5 &-10v/v 29 13 28 thd+n vs. frequency vdd=3.3v ?a rl=8 ohm ?a se ?a av= -1v/v ?a po=25 & 50 &100mw 30 13 29 thd+n vs. output power vdd=3.3v ?a rl=8 ohm ?a se ?a av= -1v/v ?a f=100 & 1k & 20khz 31 13 30 thd+n vs. frequency vdd=3.3v ?a rl=32 ohm ?a se ?a po=30mw ?a av= -1 &-5 &-10v/v 32 13 31 thd+n vs. frequency vdd=3.3v ?a rl=32 ohm ?a se ?a av= -1v/v ?a po=10 & 20 & 30mw 33 14 32 thd+n vs. output power vdd=3.3v ?a rl=32 ohm ?a se ?a av=-1v/v ?a f=20 & 1k & 20khz 34 14
EUA5202 ds5202 ver 1.4 nov. 2004 8 33 output noise voltage vs. frequency vdd=5v ?a bw=22hz to 22khz ?a rl=4 35 14 34 output noise voltage vs. frequency vdd=3.3v ?a bw=22hz to 22khz ?a rl=4 36 14 35 supply ripple rejection ratio vs. fre q uenc y rl=4 ohm ?a cb=4.7uf ?a btl ?a vdd=3.3 & 5v 37 14 36 supply ripple rejection ratio vs. frequency rl=4 ohm ?a cb=4.7uf ?a se ?a vdd=3.3 & 5v 38 14 37 crosstalk vs .frequency vdd=5v ?a po=1.5w ?a rl=4 ohm ?a btl ?a right to left & left to right 39 15 38 crosstalk vs .frequency vdd=3.3v ?a po=0.75w ?a rl=4 ohm ?a btl ?a right to left & left to right 40 15 39 crosstalk vs .frequency vdd=5v ?a po=75mw ?a rl=32 ohm ?a se ?a right to left & left to right 41 15 40 crosstalk vs .frequency vdd=3.3v ?a po=35mw ?a rl=32 ohm ?a se ?a right to left & left to right 42 15 41 closed loop response vdd=5v ?a av=-2v/v ?a po=1.5w ?a btl ?a gain & phase 43 15 42 closed loop response vdd=3.3v ?a av= -2v/v ?a po=0.75w ?a btl ?a gain &phase 44 15 43 closed loop response vdd=5v ?a av=-1v/v ?a po=0.5w ?a se ?a gain &phase 45 16 44 closed loop response vdd=3.3v ?a av= -1v/v ?a po=0.25w ?a se ?a gain &phase 46 16 45 supply current vs. supply voltage stereo btl & stereo se 47 16 46 output power vs. supply voltage thd+n=1 % ?a btl ?a each channel ?a rl=3 & 4 & 8 ohm 48 16 47 output power vs. supply voltage thd+n=1 % ?a se ?a each channel ?a rl=3 & 4 & 8 ohm 49 16 48 output power vs. load resistance thd+n=1 % ?a btl ?a each channel ?a vdd=3.3 & 5v 50 16 49 output power vs. load resistance thd+n=1 % ?a se ?a each channel ?a vdd=3.3 & 5v 51 17 50 power dissipation vs. output power vdd=5v ?a btl ?a each channel ?a rl=3 & 4 & 8ohm 52 17 51 power dissipation vs. output power vdd=3.3v ?a btl ?a each channel ?a rl=3 & 4 & 8ohm 53 17 52 power dissipation vs. output power vdd=5v ?a se ?a each channel ?a rl=4 & 8 &32 ohm 54 17 53 power dissipation vs. output power vdd=3.3v ?a se ?a each channel ?a rl=4 & 8 &32 ohm 55 17
EUA5202 ds5202 ver 1.4 nov. 2004 9 figure 3. figure 4. figure5. figure6. figure7. figure8.
EUA5202 ds5202 ver 1.4 nov. 2004 10 figure9. figure10. figure11. figure12. figure13. figure14.
EUA5202 ds5202 ver 1.4 nov. 2004 11 figure15. figure16. figure17. figure18. figure19. figure20.
EUA5202 ds5202 ver 1.4 nov. 2004 12 figure21. figure22. figure23. figure24. figure25. figure26.
EUA5202 ds5202 ver 1.4 nov. 2004 13 figure27. figure28. figure29. figure30. figure31. figure32.
EUA5202 ds5202 ver 1.4 nov. 2004 14 figure33. figure34. figure35. figure36. figure37. figure38.
EUA5202 ds5202 ver 1.4 nov. 2004 15 figure39. figure40. figure41. figure42. figure43. figure44.
EUA5202 ds5202 ver 1.4 nov. 2004 16 figure45. figure46. figure47. figure48. figure49. figure50.
EUA5202 ds5202 ver 1.4 nov. 2004 17 figure51. figure52. figure53. figure54. figure55.
EUA5202 ds5202 ver 1.4 nov. 2004 18 application information gain setting resistors, r f and r i the gain for each audio input of the EUA5202 is set by resistors by resistors r f and r i according to equation 1 for btl mode. -------------------------------- (1) btl mode operation brings about the factor 2 in the gain equation due to the inverting amplifier mirroring the voltage swing across the load. given that the EUA5202 is a mos amplifier, the input impedance is very high, value of r f increases. in addition, a certain range of r f values is required for proper start-up operation of the amplifier. taken together it is recommended that the effective impedance seen by the inverting node of the amplifier be set between 5k ? and 20k ? .the effective impedance is calculated in equation 2. -------------------- (2) as an example consider an input resistance of 10k ? and a feedback resistor of 50k ? . the btl gain of the amplifier would be -10 and the effective impedance at the inverting terminal would be 8.3k ? , which is well within the recommended range. for high performance applications metal film resistors are recommended because they tent to have lower noise levels than carbon resistors. for values of r f above 50k ? the amplifier tends to become unstable due to a pole formed from r f and the inherent input capacitance of the mos input structure. for this reason, a small compensation capacitor of approximately 5pf should be places in parallel with r f when r f is greater than 50k ? . this, in effect, creates a low pass filter network with the cutoff frequency defined in equation 3. -------------------- (3) for example, if r f is 100k ? and c f is 5 pf then f c is 318 khz, which is well outside of the audio range. input capacitor, c i in the typical application an input capacitor, c i , is required to allow the amplifier to bias the input signal to the proper dc level for optimum operation. in this case, c i and r i form a high-pass filter with the corner frequency determined in equation 4. ------------------- (4) the value of c i is important to consider as it directly affects the bass (low frequency) performance of the circuit. consider the example where r i is 10k ? and the specification calls for a flat bass response down to 40hz. equation 8 is reconfigured as equation 5. ------------------------------------ (5) in this example, c i is 0.40 f so one would likely choose a value in the range of 0.47 f to 1 f. a further consideration for this capacitor is the leakage path from the input source through the input network (r i , c i ) and the feedback resistor (r f ) to the load. this leakage current creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain applications. for this reason a low-leakage tantalum or ceramic capacitor is the best choice. when polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as the dc level there is held at v dd /2, which is likely higher that the source dc level. please note that it is important to confirm the capacitor polarity in the application. c f i r 2 1 i c = ? ? ? ? ? ? ? ? ? ? ? = i r f r 2 gain btl i f i f r r r r mpedance effectivei + = i c i r 2 1 ) c(highpass f = f c f r 2 1 (lowpass) c f =
EUA5202 ds5202 ver 1.4 nov. 2004 19 power supply decoupling, c s the EUA5202 is a high-performance cmos audio amplifier that requires adequate power supply decoupling to ensure the out put total harmonic distortion (thd) is as low as possible. power supply decoupling also prevents oscillations for long lead lengths between the amplifier and the speaker. the optimum decoupling is achieved by using two capacitors of different types of noise on the power supply leads. for higher frequency transients, spikes, or digital hash on the line, a good low equivalent ? series - resistance (esr) ceramic capacitor, typically 0.1 f placed as close as possible to the device v dd lead works best. for filtering lower ? frequency noise signals, a larger aluminum electrolytic capacitor of 10 f or greater placed near the audio power amplifier is recommended. bypass capacitor, c b the bypass capacitor, c b , is the most critical capacitor and serves several important functions. during startup or recovery from shutdown mode, c b determines the rate at which the amplifier starts up. the second function is to reduce noise produced by the power supply caused by coupling into the output drive signal. this noise is from the midrail generation circuit internal to the amplifier, which appears as degraded psrr and thd+n. bypass capacitor, c b , values of 0.1 f to 1 f ceramic of tantalum low-esr capacitors are recommended for the best thd and noise performance. in figure 2, the full feature configuration, two bypass capacitors are used. this provides the maximum separation between right and left drive circuits.when absolute minimum cost and/or component space is required, one bypass capacitor can be used as shown in figure 1. it is critical that terminals 6 and 19 be tied together in this configuration. output coupling capacitor, c c in the typical single-supply se configuration, and output coupling capacitor (c c ) is required to block the dc bias at the output of the amplifie r thus preventing dc currents in the load. as with the input coupling capacitor and impedance of the load form a high-pass filter governed by equation 6 f c(high) = ---------------------------- (6) the main disadvantage, from a performance standpoint, is the load impedances are typically small, which drives the low-frequency corner higher degrading the bass response. large values of c c are required to pass low frequencies into the load. consider the example where a c c of 330 f is chosen and loads vary from 3 ? , 4 ? , 8 ? , 32 ? , 10k ? , to 47k ? . table 1 summarizes the frequency response characteristics of each configuration. table1. common load impedances vs low frequency output characteristics in se mode r l c c lowest frequency 3 ? 330 f 161 hz 4 ? 330 f 120 hz 8 ? 330 f 60 hz 32 ? 330 f 15 hz 10000 ? 330 f 0.05 hz 47000 ? 330 f 0.01 hz as table 1 indicates, most of the bass response is attenuated into 4? ? load, an 8? ? load is adequate, headphone response is good, and drive into line level inputs (a home stereo for example) is exceptional. using low-esr capacitors low-esr capacitors are recommended throughout this applications section. a real (as opposed to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. the voltage drop across this resistor minimizes the benefi cial effects of the capacitor in the circuit. the lower th e equivalent value of this resistance the more the real capacitor behaves like an ideal capacitor. bridged-tied load versus single-ended mode figure 56 show a linear audio power amplifier (apa) in a btl configuration. the eua 5202 btl amplifier consists of two linear amplifiers driving both ends of the load. there are several potential benefits to this differential drive configuration, but initially consider power to the load. the differential drive to the speaker means that as one side is slewing up, the other side is slewing down, and vice versa. this in effect doubles the voltage swing on the load as compared to a ground referenced load. plugging 2 v o(pp) into the power equation, where voltage is squared, yields 4 the output power from the same supply rail and load impedance (see equation 7 ) v (rms) ? power ? ------ (7) 2 2 o(pp) v l r 2 (rms) v c c r 2 1 l
EUA5202 ds5202 ver 1.4 nov. 2004 20 in a typical computer sound channel operating at 5v, bridging raises the power into an 8- ? speaker from a singled -ended (se, ground reference) limit of 250 mw to 1w. in sound power that is a 6-db improvement? which is loudness that can be heard. in addition to increased power there are frequency response concerns. consider the single-supply se configuration shown in figure 57. a coupling capacitor is required to block the dc offset voltage from reaching the load. these capacitors can be quite large (approximately 33 f to 1000 f) so they tend to be expensive, heavy, occupy valuable pcb area, and have the additional drawback of limiting low-frequency performance of the system. this frequency limiting effect is due to the high pass filter network created with the speaker impedance and the coupling capacitance and is calculated with equation 8. f c = c l c r 2 1 ------------------------------------ (8) for example, a 68 f capacitor with an 8- ? speaker would attenuate low frequencies below 293 hz. the btl configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. low-frequency performance is then limited only by the input network and speaker response. cost and pcb space are also minimized by eliminating the bulky coupling capacitor. increasing power to the load does carry a penalty of increased internal power dissipation. the increased dissipation is understandable considering that the btl configuration produces 4 ?? the output power of the se configuration. internal dissi pation versus output power is discussed further in the crest factor and thermal considerations section . s ingle-ended operation in se mode (see figure56 and figure57), the load is driven from the primary amplifier output for each channel (out+, terminals 22 and 3). in se mode the gain is set by the r f and r i resistors and is shown in equation 9. since the inverting amplifier is not used to mirror the voltage swing on the load, the factor of 2, from equati on 5, is not included. se gain = ? ? ? ? ? ? ? ? ? ? ? i r f r -------------------------------------- (9) the output coupling capacito r required in single-supply se mode also places additional constraints on the selection of other components in the amplifier circuit. the rules described earlier still hold with the addition of the following relationship (see equation 10): c c l r 1 i r i c 1 k 25 b c 1 < ? ? ? ? ? ? ? ? ? ? ? ? [ --------------- (10)
EUA5202 ds5202 ver 1.4 nov. 2004 21 input mux operation working in concert with the btl se/ feature, the line hp/ mux feature gives the audio designer the flexibility of a multichip design in a single ic (see figure 58). the primary function of the mux is to allow different gain settings for btl versus se mode. speakers typically require a pproximately a factor of 10 more gain for similar volume listening levels as compared to headphones. to achieve headphone and speaker listening parity, the resistor values would need to be set as follows: -------------------------- (11) if, for example r i (hp) = 10 k ? and r f (hp) = 10k ? then se gain (hp) = -1 ? ? ? ? ? ? ? ? ? ? ? = (line) i (line) f (line) r r 2 gain btl -------------------- (12) if, for example r i (line) = 10k ? and r f (line) = 50k ? then btl gain (line) = -10 another advantage of using the mux feature is setting the gain of the headphone channel to -1. this provides the optimum distortion performance into the headphones where clear sound is more important. refer to the btl se/ operation section for a description of the headphone hack control circuit. btl se/ operation the ability of the EUA5202 to easily switch between btl and se modes is one of its most important cost saving features. this feature eliminates the requirement for an additional headphone amplifier in applications where internal stereo speakers are driven in btl mode but external headphone or speakers must be accommodated. internal to the EUA5202, two separate amplifiers drive lout- and rout- (terminals 10 and 15).when btl se/ is held high, the out- amplifier are in high output impedance st ate, which configures the EUA5202 as an se driver from lout + and rout + (terminal 3 and 22). i dd is reduced by approximately one-half in se mode. control of the btl se/ input can be from a logic-level cmos source, or, more typically, from a resistor divider network as shown in figure 59. using a readily available 1/8-in. (3.5mm) stereo headphone jack, the control switch is closed when no plug is inserted. when closed the 100-k ? / 1-k ? divider pulls the btl se/ input low. when a plug is inserted, the out- amplifier is shutdown causing the speaker to mute (virtually open-circuits the speaker). the out+ amplifier then drives through the output capacitor (co) into the headphone jack. as shown n the full feature application (figure 2), the input mux control can be tied to the btl se/ input. the benefits of doing this are described in the following input mux operation section. mute and shutdown mode the EUA5202 employs both a mute and a shutdown mode of operation designed to reduce supply current, i dd , to the absolute minimum level during periods of nonuse for battery-power conservation. the shutdown input terminal should be held low during normal operation when the amplifier is in use. pulling shutdown high causes the outputs to mute and the amplifier to enter a low-current state, i dd = 5 a. shutdown or mute in should never be left unconnected because amplifier operation would be unpredictable. mute mode alone reduces i dd to 1.5 ma. ? ? ? ? ? ? ? ? ? ? ? = (hp) i (hp) f (hp) r r gain se
EUA5202 ds5202 ver 1.4 nov. 2004 22 package information note 1. package body sizes exclude mold flash protrusions or gate burrs 2. tolerance 0.1mm unless otherwise specified 3. coplanarity :0.1mm 4. controlling dimension is millimeter. converte d inch dimensions are not necessarily exact. 5. die pad exposure size is acco rding to lead frame design. 6. standard solder map dimension is millimeter. 7. followed from jedec mo-153 dimensions in millimeters dimensions in inches symbols min. nom. max. min. nom. max. a ------ ------ 1.15 ------ ------ 0.045 a1 0.00 ------ 0.10 0.000 ------ 0.004 a2 0.80 1.00 1.05 0.031 0.039 0.041 b 0.19 ------ 0.30 0.007 ------ 0.012 c 0.09 ------ 0.20 0.004 ------ 0.008 d 7.70 7.80 7.90 0.303 0.307 0.311 e ------ 6.40 ----- ------ 0.252 ------ e1 4.30 4.40 4.50 0.169 0.173 0.177 e ------ 0.65 ----- ------ 0.026 ------ l 0.45 0.60 0.75 0.018 0.024 0.030 y ------ ------ 0.10 ------ ------ 0.004 0 ------ 8 0 ------ 8 use as much copper area as possible bottom view exposed pad

▲Up To Search▲

Price & Availability of EUA5202

	To Download EUA5202 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .